For all dimensions see corresponding reference letters in table.
Angle between sides of thread is 60 degrees. Taper of thread, on diameter, is 3/4 inch per foot. Angle of taper with centerline is 1 °47'.
The basic maximum thread height of the truncated thread is 0.8Xpitch of thread. The crest and root are truncated a minimum of 0.033Xpitch for all pitches.
*** All dimensions are given in inches.
Nominal Pipe Size |
Outside Diameter of Pipe |
Threads per Inch |
Pitch of Thread |
Pitch Diameter at Beginning of External Thread |
Handtight Engagement |
Effective Thread, External |
Wrench Makeup Length for Internal Thread |
Vanish Thread |
Overall Length External Thread |
Nominal Perfect External Threads |
Height of Thread |
Basic Minor Diameter at Small End of Pipe |
|||||
Length |
Diameter |
Length |
Diameter |
Length |
- |
Diameter |
Length |
Diameter |
|||||||||
See Note |
See Note |
See Note |
- |
See Note |
- |
- |
- |
- |
|||||||||
< 2 > |
< 3 > |
< 4 > |
- |
< 7 > |
- |
- |
- |
- |
See Note |
||||||||
In. |
- |
In. |
- |
- |
- |
- |
- |
- |
< 6 > |
||||||||
- |
(D) |
(n) |
(p) |
(Eo) |
(L1) |
(E1) |
(L2) |
(E2) |
(L3) |
- |
(E3) |
(V) |
(L4) |
(L5) |
(E5) |
(h) |
(Ko) |
1/16 |
0.313 |
27 |
0.03704 |
0.27118 |
0.1600 |
0.28118 |
0.2611 |
0.28750 |
0.1111 |
- |
0.26424 |
0.1285 |
0.3896 |
0.1870 |
0.28287 |
0.02963 |
0.2416 |
1/8 |
0.405 |
27 |
0.03704 |
0.36351 |
0.1615 |
0.37360 |
0.2639 |
0.38000 |
0.1111 |
- |
0.35656 |
0.1285 |
0.3924 |
0.1898 |
0.37537 |
0.02963 |
0.3339 |
1/4 |
0.540 |
18 |
0.05556 |
0.47739 |
0.2278 |
0.49163 |
0.4018 |
0.50250 |
0.1667 |
- |
0.46697 |
0.1928 |
0.5946 |
0.2907 |
0.49556 |
0.04444 |
0.4329 |
3/8 |
0.675 |
18 |
0.05556 |
0.61201 |
0.2400 |
0.62701 |
0.4078 |
0.63750 |
0.1667 |
- |
0.60160 |
0.1928 |
0.6006 |
0.2967 |
0.63056 |
0.04444 |
0.5676 |
1/2 |
0.840 |
14 |
0.07143 |
0.75843 |
0.3200 |
0.77843 |
0.5337 |
0.79179 |
0.2143 |
- |
0.74504 |
0.2478 |
0.7815 |
0.3909 |
0.78286 |
0.05714 |
0.7013 |
3/4 |
1.050 |
14 |
0.07143 |
0.96768 |
0.3390 |
0.98887 |
0.5457 |
1.00179 |
0.2143 |
- |
0.95492 |
0.2478 |
0.7935 |
0.4029 |
0.99286 |
0.05714 |
0.9105 |
1 |
1.315 |
11 1/2 |
0.08696 |
1.21363 |
0.4000 |
1.23863 |
0.6828 |
1.25630 |
0.2609 |
- |
1.19733 |
0.3017 |
0.9845 |
0.5089 |
1.24543 |
0.06957 |
1.1441 |
1 1/4 |
1.660 |
11 1/2 |
0.08696 |
1.55713 |
0.4200 |
1.58338 |
0.7068 |
1.60130 |
0.2609 |
- |
1.54083 |
0.3017 |
1.0085 |
0.5329 |
1.59043 |
0.06957 |
1.4876 |
1 1/2 |
1.900 |
11 1/2 |
0.08696 |
1.79609 |
0.4200 |
1.82234 |
0.7235 |
1.84130 |
0.2609 |
- |
1.77978 |
0.3017 |
1.0252 |
0.5496 |
1.83043 |
0.06957 |
1.7265 |
2 |
2.375 |
11 1/2 |
0.08696 |
2.26902 |
0.4360 |
2.29627 |
0.7565 |
2.31630 |
0.2609 |
- |
2.25272 |
0.3017 |
1.0582 |
0.5826 |
2.30543 |
0.06957 |
2.1995 |
2 1/2 |
2.875 |
8 |
0.12500 |
2.71953 |
0.6820 |
2.76216 |
1.1375 |
2.79062 |
0.2500 |
See Note < 8 > |
2.70391 |
0.4337 |
1.5712 |
0.8875 |
2.77500 |
0.1 |
2.6195 |
3 |
3.500 |
8 |
0.12500 |
3.34062 |
0.7660 |
3.38850 |
1.2000 |
3.41562 |
0.2500 |
See Note < 8 > |
3.32500 |
0.4337 |
1.6337 |
0.9500 |
3.40000 |
0.1 |
3.2406 |
3 1/2 |
4.000 |
8 |
0.12500 |
3.83750 |
0.8210 |
3.88881 |
1.2500 |
3.91562 |
0.2500 |
- |
3.82188 |
0.4337 |
1.6837 |
1.0000 |
3.90000 |
0.1 |
3.7375 |
4 |
4.500 |
8 |
0.12500 |
4.33438 |
0.8440 |
4.38712 |
1.3000 |
4.41562 |
0.2500 |
- |
4.31875 |
0.4337 |
1.7337 |
1.0500 |
4.40000 |
0.1 |
4.2344 |
5 |
5.563 |
8 |
0.12500 |
5.39073 |
0.9370 |
5.44929 |
1.4063 |
5.47862 |
0.2500 |
- |
5.37511 |
0.4337 |
1.8400 |
1.1563 |
5.46300 |
0.1 |
5.2907 |
6 |
6.625 |
8 |
0.12500 |
6.44609 |
0.9580 |
6.50597 |
1.5125 |
6.54062 |
0.2500 |
- |
6.43047 |
0.4337 |
1.9462 |
1.2625 |
6.52500 |
0.1 |
6.3461 |
8 |
8.625 |
8 |
0.12500 |
8.43359 |
1.0630 |
8.50003 |
1.7125 |
8.54062 |
0.2500 |
- |
8.41797 |
0.4337 |
2.1462 |
1.4625 |
8.52500 |
0.1 |
8.3336 |
10 |
10.750 |
8 |
0.12500 |
10.54531 |
1.2100 |
10.62094 |
1.9250 |
10.66562 |
0.2500 |
- |
10.52969 |
0.4337 |
2.3587 |
1.6750 |
10.65000 |
0.1 |
10.4453 |
Note < 1>
The basic dimension of the ANSI standard taper pipe thread are given in inches to four or five decimal places. While this implies a greater degree of precision than is ordinarily attained, these dimensions are the basis of gage dimensions and are so expressed for the purpose of eliminating errors in computations.
Note < 2 >
Also length of thin ring gage and length from gaging notch to small end of plug age.
Note < 3 >
Also pitch diameter at gaging notch (handtight plane).
Note < 4 >
Also length of plug gage.
Note < 5 >
The length L5 from the end of the pipe determines the plane beyond which the thread form is imperfect at the crest. The next tow threads are perfect at the root. At this plane the cone formed by the crests of the thread intersects the cylinder forming the external surface of the pipe. L5=L2-2p
Note < 6 >
Given as information for use in selecting tap drills.
Note < 7 >
Three threads for 2-inch size and smaller; two threads for larger sizes.
Note < 8 >
Military Specification MIL-P-7105 gives the wrench makeup as three threads for 3 in. and smaller. The E3 dimensions are then as follows: Size 2 1/2 in., 2.69609 and size 3 in., 3.31719. Increase in diameter per thread is equal to 0.0625/n.
***** The above data sheet can be used for information purpose only. No responsibility can be accepted for errors or omissions by whatever cause.
CNC Machine Parts
*** Pipe Thread ***
The Type of the threads used on pipe and pipe fittings may be classed according tointended use;
1) threads which when assembled with a sealer will produce a pressure-tight joint
2) threads witch when assembled without a sealer will produce a pressure-tight joint
3) threads witch provide free- and loose fitting mechanical joints without pressure thightness
4) threads wich produce rigid mechanical joints without pressure tightness
CNC Machining and Turned Parts
Do you need a quick turn around on CNC machining and turned parts??
